...

RL Circuits

by taratuta

on
Category: Documents
11

views

Report

Comments

Transcript

RL Circuits
CHAPTER 23 | ELECTROMAGNETIC INDUCTION, AC CIRCUITS, AND ELECTRICAL TECHNOLOGIES
(4π×10 −7 T ⋅ m/A)(200) 2(1.26×10 −3 m 2)
0.100 m
= 0.632 mH.
L =
(23.42)
Discussion
This solenoid is moderate in size. Its inductance of nearly a millihenry is also considered moderate.
One common application of inductance is used in traffic lights that can tell when vehicles are waiting at the intersection. An electrical circuit with an
inductor is placed in the road under the place a waiting car will stop over. The body of the car increases the inductance and the circuit changes
sending a signal to the traffic lights to change colors. Similarly, metal detectors used for airport security employ the same technique. A coil or inductor
in the metal detector frame acts as both a transmitter and a receiver. The pulsed signal in the transmitter coil induces a signal in the receiver. The
self-inductance of the circuit is affected by any metal object in the path. Such detectors can be adjusted for sensitivity and also can indicate the
approximate location of metal found on a person. (But they will not be able to detect any plastic explosive such as that found on the “underwear
bomber.”) See Figure 23.43.
Figure 23.43 The familiar security gate at an airport can not only detect metals but also indicate their approximate height above the floor. (credit: Alexbuirds, Wikimedia
Commons)
Energy Stored in an Inductor
We know from Lenz’s law that inductances oppose changes in current. There is an alternative way to look at this opposition that is based on energy.
Energy is stored in a magnetic field. It takes time to build up energy, and it also takes time to deplete energy; hence, there is an opposition to rapid
change. In an inductor, the magnetic field is directly proportional to current and to the inductance of the device. It can be shown that the energy
stored in an inductor E ind is given by
E ind = 1 LI 2.
2
(23.43)
This expression is similar to that for the energy stored in a capacitor.
Example 23.8 Calculating the Energy Stored in the Field of a Solenoid
How much energy is stored in the 0.632 mH inductor of the preceding example when a 30.0 A current flows through it?
Strategy
The energy is given by the equation
E ind = 1 LI 2 , and all quantities except E ind are known.
2
Solution
Substituting the value for
L found in the previous example and the given current into E ind = 1 LI 2 gives
2
E ind = 1 LI 2
2
= 0.5(0.632×10 −3 H)(30.0 A) 2 = 0.284 J.
(23.44)
Discussion
This amount of energy is certainly enough to cause a spark if the current is suddenly switched off. It cannot be built up instantaneously unless
the power input is infinite.
23.10 RL Circuits
We know that the current through an inductor L cannot be turned on or off instantaneously. The change in current changes flux, inducing an emf
opposing the change (Lenz’s law). How long does the opposition last? Current will flow and can be turned off, but how long does it take? Figure
23.44 shows a switching circuit that can be used to examine current through an inductor as a function of time.
839
840
CHAPTER 23 | ELECTROMAGNETIC INDUCTION, AC CIRCUITS, AND ELECTRICAL TECHNOLOGIES
Figure 23.44 (a) An RL circuit with a switch to turn current on and off. When in position 1, the battery, resistor, and inductor are in series and a current is established. In
position 2, the battery is removed and the current eventually stops because of energy loss in the resistor. (b) A graph of current growth versus time when the switch is moved
to position 1. (c) A graph of current decay when the switch is moved to position 2.
When the switch is first moved to position 1 (at
t = 0 ), the current is zero and it eventually rises to I 0 = V/R , where R is the total resistance of
the circuit. The opposition of the inductor L is greatest at the beginning, because the amount of change is greatest. The opposition it poses is in the
form of an induced emf, which decreases to zero as the current approaches its final value. The opposing emf is proportional to the amount of change
left. This is the hallmark of an exponential behavior, and it can be shown with calculus that
I = I 0(1 − e −t / τ) (turning on),
(23.45)
is the current in an RL circuit when switched on (Note the similarity to the exponential behavior of the voltage on a charging capacitor). The initial
current is zero and approaches I 0 = V/R with a characteristic time constant τ for an RL circuit, given by
τ = L,
R
where
(23.46)
τ has units of seconds, since 1 H=1 Ω·s . In the first period of time τ , the current rises from zero to 0.632I 0 , since
I = I 0(1 − e −1) = I 0(1 − 0.368) = 0.632I 0 . The current will go 0.632 of the remainder in the next time τ . A well-known property of the
exponential is that the final value is never exactly reached, but 0.632 of the remainder to that value is achieved in every characteristic time τ . In just
a few multiples of the time τ , the final value is very nearly achieved, as the graph in Figure 23.44(b) illustrates.
τ depends on only two factors, the inductance L and the resistance R . The greater the inductance L , the greater τ is,
R , the greater τ is. Again this makes
sense, since a small resistance means a large final current and a greater change to get there. In both cases—large L and small R —more energy
The characteristic time
which makes sense since a large inductance is very effective in opposing change. The smaller the resistance
is stored in the inductor and more time is required to get it in and out.
When the switch in Figure 23.44(a) is moved to position 2 and cuts the battery out of the circuit, the current drops because of energy dissipation by
the resistor. But this is also not instantaneous, since the inductor opposes the decrease in current by inducing an emf in the same direction as the
battery that drove the current. Furthermore, there is a certain amount of energy, (1/2)LI 02 , stored in the inductor, and it is dissipated at a finite rate.
As the current approaches zero, the rate of decrease slows, since the energy dissipation rate is I 2 R . Once again the behavior is exponential, and
I is found to be
I = I 0e −t / τ
(23.47)
(turning off).
(See Figure 23.44(c).) In the first period of time τ = L / R after the switch is closed, the current falls to 0.368 of its initial value, since
I = I 0e −1 = 0.368I 0 . In each successive time τ , the current falls to 0.368 of the preceding value, and in a few multiples of τ , the current
becomes very close to zero, as seen in the graph in Figure 23.44(c).
Example 23.9 Calculating Characteristic Time and Current in an RL Circuit
(a) What is the characteristic time constant for a 7.50 mH inductor in series with a
is moved to position 2 to disconnect the battery, if it is initially 10.0 A.
3.00 Ω resistor? (b) Find the current 5.00 ms after the switch
Strategy for (a)
The time constant for an RL circuit is defined by
τ = L/R.
Solution for (a)
Entering known values into the expression for
τ given in τ = L / R yields
τ = L = 7.50 mH = 2.50 ms.
R 3.00 Ω
Discussion for (a)
This is a small but definitely finite time. The coil will be very close to its full current in about ten time constants, or about 25 ms.
This content is available for free at http://cnx.org/content/col11406/1.7
(23.48)
Fly UP