...

Friction

by taratuta

on
Category: Documents
8

views

Report

Comments

Description

Transcript

Friction
166
CHAPTER 5 | FURTHER APPLICATIONS OF NEWTON'S LAWS: FRICTION, DRAG, AND ELASTICITY
Introduction: Further Applications of Newton’s Laws
Describe the forces on the hip joint. What means are taken to ensure that this will be a good movable joint? From the photograph (for an adult) in
Figure 5.1, estimate the dimensions of the artificial device.
It is difficult to categorize forces into various types (aside from the four basic forces discussed in previous chapter). We know that a net force affects
the motion, position, and shape of an object. It is useful at this point to look at some particularly interesting and common forces that will provide
further applications of Newton’s laws of motion. We have in mind the forces of friction, air or liquid drag, and deformation.
5.1 Friction
Friction is a force that is around us all the time that opposes relative motion between systems in contact but also allows us to move (which you have
discovered if you have ever tried to walk on ice). While a common force, the behavior of friction is actually very complicated and is still not completely
understood. We have to rely heavily on observations for whatever understandings we can gain. However, we can still deal with its more elementary
general characteristics and understand the circumstances in which it behaves.
Friction
Friction is a force that opposes relative motion between systems in contact.
One of the simpler characteristics of friction is that it is parallel to the contact surface between systems and always in a direction that opposes motion
or attempted motion of the systems relative to each other. If two systems are in contact and moving relative to one another, then the friction between
them is called kinetic friction. For example, friction slows a hockey puck sliding on ice. But when objects are stationary, static friction can act
between them; the static friction is usually greater than the kinetic friction between the objects.
Kinetic Friction
If two systems are in contact and moving relative to one another, then the friction between them is called kinetic friction.
Imagine, for example, trying to slide a heavy crate across a concrete floor—you may push harder and harder on the crate and not move it at all. This
means that the static friction responds to what you do—it increases to be equal to and in the opposite direction of your push. But if you finally push
hard enough, the crate seems to slip suddenly and starts to move. Once in motion it is easier to keep it in motion than it was to get it started,
indicating that the kinetic friction force is less than the static friction force. If you add mass to the crate, say by placing a box on top of it, you need to
push even harder to get it started and also to keep it moving. Furthermore, if you oiled the concrete you would find it to be easier to get the crate
started and keep it going (as you might expect).
Figure 5.2 is a crude pictorial representation of how friction occurs at the interface between two objects. Close-up inspection of these surfaces shows
them to be rough. So when you push to get an object moving (in this case, a crate), you must raise the object until it can skip along with just the tips
of the surface hitting, break off the points, or do both. A considerable force can be resisted by friction with no apparent motion. The harder the
surfaces are pushed together (such as if another box is placed on the crate), the more force is needed to move them. Part of the friction is due to
adhesive forces between the surface molecules of the two objects, which explain the dependence of friction on the nature of the substances.
Adhesion varies with substances in contact and is a complicated aspect of surface physics. Once an object is moving, there are fewer points of
contact (fewer molecules adhering), so less force is required to keep the object moving. At small but nonzero speeds, friction is nearly independent of
speed.
Figure 5.2 Frictional forces, such as
f
, always oppose motion or attempted motion between objects in contact. Friction arises in part because of the roughness of the
surfaces in contact, as seen in the expanded view. In order for the object to move, it must rise to where the peaks can skip along the bottom surface. Thus a force is required
just to set the object in motion. Some of the peaks will be broken off, also requiring a force to maintain motion. Much of the friction is actually due to attractive forces between
molecules making up the two objects, so that even perfectly smooth surfaces are not friction-free. Such adhesive forces also depend on the substances the surfaces are made
of, explaining, for example, why rubber-soled shoes slip less than those with leather soles.
The magnitude of the frictional force has two forms: one for static situations (static friction), the other for when there is motion (kinetic friction).
When there is no motion between the objects, the magnitude of static friction
f s is
f s ≤ µ sN,
where
µ s is the coefficient of static friction and N is the magnitude of the normal force (the force perpendicular to the surface).
This content is available for free at http://cnx.org/content/col11406/1.7
(5.1)
CHAPTER 5 | FURTHER APPLICATIONS OF NEWTON'S LAWS: FRICTION, DRAG, AND ELASTICITY
Magnitude of Static Friction
Magnitude of static friction
f s is
f s ≤ µ sN,
where
(5.2)
µ s is the coefficient of static friction and N is the magnitude of the normal force.
The symbol
≤ means less than or equal to, implying that static friction can have a minimum and a maximum value of µ s N . Static friction is a
responsive force that increases to be equal and opposite to whatever force is exerted, up to its maximum limit. Once the applied force exceeds
f s(max) , the object will move. Thus
f s(max) = µ sN.
Once an object is moving, the magnitude of kinetic friction
(5.3)
f k is given by
f k = µ kN,
where
(5.4)
µ k is the coefficient of kinetic friction. A system in which f k = µ kN is described as a system in which friction behaves simply.
Magnitude of Kinetic Friction
The magnitude of kinetic friction
f k is given by
f k = µ kN,
where
(5.5)
µ k is the coefficient of kinetic friction.
As seen in Table 5.1, the coefficients of kinetic friction are less than their static counterparts. That values of
µ in Table 5.1 are stated to only one or,
at most, two digits is an indication of the approximate description of friction given by the above two equations.
Table 5.1 Coefficients of Static and Kinetic Friction
Static friction µs
Kinetic friction µk
Rubber on dry concrete
1.0
0.7
Rubber on wet concrete
0.7
0.5
Wood on wood
0.5
0.3
Waxed wood on wet snow
0.14
0.1
Metal on wood
0.5
0.3
Steel on steel (dry)
0.6
0.3
Steel on steel (oiled)
0.05
0.03
System
Teflon on steel
0.04
0.04
Bone lubricated by synovial fluid
0.016
0.015
Shoes on wood
0.9
0.7
Shoes on ice
0.1
0.05
Ice on ice
0.1
0.03
Steel on ice
0.4
0.02
The equations given earlier include the dependence of friction on materials and the normal force. The direction of friction is always opposite that of
motion, parallel to the surface between objects, and perpendicular to the normal force. For example, if the crate you try to push (with a force parallel
to the floor) has a mass of 100 kg, then the normal force would be equal to its weight, W = mg = (100 kg)(9.80 m/s 2) = 980 N , perpendicular to
the floor. If the coefficient of static friction is 0.45, you would have to exert a force parallel to the floor greater than
f s(max) = µ sN = (0.45)(980 N) = 440 N to move the crate. Once there is motion, friction is less and the coefficient of kinetic friction might be
0.30, so that a force of only 290 N ( f k = µ kN = (0.30)(980 N) = 290 N ) would keep it moving at a constant speed. If the floor is lubricated, both
coefficients are considerably less than they would be without lubrication. Coefficient of friction is a unit less quantity with a magnitude usually between
0 and 1.0. The coefficient of the friction depends on the two surfaces that are in contact.
167
168
CHAPTER 5 | FURTHER APPLICATIONS OF NEWTON'S LAWS: FRICTION, DRAG, AND ELASTICITY
Take-Home Experiment
Find a small plastic object (such as a food container) and slide it on a kitchen table by giving it a gentle tap. Now spray water on the table,
simulating a light shower of rain. What happens now when you give the object the same-sized tap? Now add a few drops of (vegetable or olive)
oil on the surface of the water and give the same tap. What happens now? This latter situation is particularly important for drivers to note,
especially after a light rain shower. Why?
Many people have experienced the slipperiness of walking on ice. However, many parts of the body, especially the joints, have much smaller
coefficients of friction—often three or four times less than ice. A joint is formed by the ends of two bones, which are connected by thick tissues. The
knee joint is formed by the lower leg bone (the tibia) and the thighbone (the femur). The hip is a ball (at the end of the femur) and socket (part of the
pelvis) joint. The ends of the bones in the joint are covered by cartilage, which provides a smooth, almost glassy surface. The joints also produce a
fluid (synovial fluid) that reduces friction and wear. A damaged or arthritic joint can be replaced by an artificial joint (Figure 5.3). These replacements
can be made of metals (stainless steel or titanium) or plastic (polyethylene), also with very small coefficients of friction.
Figure 5.3 Artificial knee replacement is a procedure that has been performed for more than 20 years. In this figure, we see the post-op x rays of the right knee joint
replacement. (credit: Mike Baird, Flickr)
Other natural lubricants include saliva produced in our mouths to aid in the swallowing process, and the slippery mucus found between organs in the
body, allowing them to move freely past each other during heartbeats, during breathing, and when a person moves. Artificial lubricants are also
common in hospitals and doctor’s clinics. For example, when ultrasonic imaging is carried out, a gel is used to lubricate the surface between the
transducer and the skin—thereby reducing the coefficient of friction between the two surfaces. This allows the transducer to mover freely over the
skin.
Example 5.1 Skiing Exercise
A skier with a mass of 62 kg is sliding down a snowy slope. Find the coefficient of kinetic friction for the skier if friction is known to be 45.0 N.
Strategy
The magnitude of kinetic friction was given in to be 45.0 N. Kinetic friction is related to the normal force
N as f k = µ kN ; thus, the coefficient
of kinetic friction can be found if we can find the normal force of the skier on a slope. The normal force is always perpendicular to the surface,
and since there is no motion perpendicular to the surface, the normal force should equal the component of the skier’s weight perpendicular to the
slope. (See the skier and free-body diagram in Figure 5.4.)
This content is available for free at http://cnx.org/content/col11406/1.7
CHAPTER 5 | FURTHER APPLICATIONS OF NEWTON'S LAWS: FRICTION, DRAG, AND ELASTICITY
Figure 5.4 The motion of the skier and friction are parallel to the slope and so it is most convenient to project all forces onto a coordinate system where one axis is
N (the normal force) is perpendicular to the slope, and f (the friction) is parallel to the
w ⊥ and W // . N is equal in magnitude to w⊥ , so there is no motion perpendicular to
parallel to the slope and the other is perpendicular (axes shown to left of skier).
slope, but
w
(the skier’s weight) has components along both axes, namely
the slope. However,
f
is less than
W //
in magnitude, so there is acceleration down the slope (along the x-axis).
That is,
N = w⊥ = w cos 25º = mg cos 25º.
(5.6)
Substituting this into our expression for kinetic friction, we get
f k = µ kmg cos 25º,
which can now be solved for the coefficient of kinetic friction
(5.7)
µk .
Solution
Solving for
µ k gives
µk =
fk
=
N
fk
w cos 25º
=
fk
(5.8)
mg cos 25º.
Substituting known values on the right-hand side of the equation,
µk =
45.0 N
= 0.082.
(62 kg)(9.80 m/s 2)(0.906)
(5.9)
Discussion
This result is a little smaller than the coefficient listed in Table 5.1 for waxed wood on snow, but it is still reasonable since values of the
coefficients of friction can vary greatly. In situations like this, where an object of mass m slides down a slope that makes an angle θ with the
horizontal, friction is given by
f k = µ kmg cos θ . All objects will slide down a slope with constant acceleration under these circumstances. Proof
of this is left for this chapter’s Problems and Exercises.
Take-Home Experiment
An object will slide down an inclined plane at a constant velocity if the net force on the object is zero. We can use this fact to measure the
coefficient of kinetic friction between two objects. As shown in Example 5.1, the kinetic friction on a slope f k = µ kmg cos θ . The component of
the weight down the slope is equal to
mg sin θ (see the free-body diagram in Figure 5.4). These forces act in opposite directions, so when they
have equal magnitude, the acceleration is zero. Writing these out:
f k = Fg x
Solving for
(5.10)
µ k mg cos θ = mg sin θ.
(5.11)
mg sin θ
= tan θ.
mg cos θ
(5.12)
µ k , we find that
µk =
Put a coin on a book and tilt it until the coin slides at a constant velocity down the book. You might need to tap the book lightly to get the coin to
move. Measure the angle of tilt relative to the horizontal and find µ k . Note that the coin will not start to slide at all until an angle greater than θ
is attained, since the coefficient of static friction is larger than the coefficient of kinetic friction. Discuss how this may affect the value for
its uncertainty.
µ k and
169
170
CHAPTER 5 | FURTHER APPLICATIONS OF NEWTON'S LAWS: FRICTION, DRAG, AND ELASTICITY
We have discussed that when an object rests on a horizontal surface, there is a normal force supporting it equal in magnitude to its weight.
Furthermore, simple friction is always proportional to the normal force.
Making Connections: Submicroscopic Explanations of Friction
The simpler aspects of friction dealt with so far are its macroscopic (large-scale) characteristics. Great strides have been made in the atomicscale explanation of friction during the past several decades. Researchers are finding that the atomic nature of friction seems to have several
fundamental characteristics. These characteristics not only explain some of the simpler aspects of friction—they also hold the potential for the
development of nearly friction-free environments that could save hundreds of billions of dollars in energy which is currently being converted
(unnecessarily) to heat.
Figure 5.5 illustrates one macroscopic characteristic of friction that is explained by microscopic (small-scale) research. We have noted that friction is
proportional to the normal force, but not to the area in contact, a somewhat counterintuitive notion. When two rough surfaces are in contact, the
actual contact area is a tiny fraction of the total area since only high spots touch. When a greater normal force is exerted, the actual contact area
increases, and it is found that the friction is proportional to this area.
Figure 5.5 Two rough surfaces in contact have a much smaller area of actual contact than their total area. When there is a greater normal force as a result of a greater applied
force, the area of actual contact increases as does friction.
But the atomic-scale view promises to explain far more than the simpler features of friction. The mechanism for how heat is generated is now being
determined. In other words, why do surfaces get warmer when rubbed? Essentially, atoms are linked with one another to form lattices. When
surfaces rub, the surface atoms adhere and cause atomic lattices to vibrate—essentially creating sound waves that penetrate the material. The
sound waves diminish with distance and their energy is converted into heat. Chemical reactions that are related to frictional wear can also occur
between atoms and molecules on the surfaces. Figure 5.6 shows how the tip of a probe drawn across another material is deformed by atomic-scale
friction. The force needed to drag the tip can be measured and is found to be related to shear stress, which will be discussed later in this chapter. The
variation in shear stress is remarkable (more than a factor of 10 12 ) and difficult to predict theoretically, but shear stress is yielding a fundamental
understanding of a large-scale phenomenon known since ancient times—friction.
Figure 5.6 The tip of a probe is deformed sideways by frictional force as the probe is dragged across a surface. Measurements of how the force varies for different materials
are yielding fundamental insights into the atomic nature of friction.
PhET Explorations: Forces and Motion
Explore the forces at work when you try to push a filing cabinet. Create an applied force and see the resulting friction force and total force acting
on the cabinet. Charts show the forces, position, velocity, and acceleration vs. time. Draw a free-body diagram of all the forces (including
gravitational and normal forces).
This content is available for free at http://cnx.org/content/col11406/1.7
Fly UP