...

パワーアンプ内蔵ボリュームパネル

by user

on
Category: Documents
0

views

Report

Comments

Transcript

パワーアンプ内蔵ボリュームパネル
RDL
製品応用例
パワーアンプ内蔵ボリュームパネル
信号ラインは汎用の LAN ケーブルで接続可能
1. D(S,B)-TPA1A 3.5W パワーアンプ内蔵ボリュームパネル ¥32,400






壁面パネルに 3.5 ㍗/8 ㌊のパワーアンプが内蔵
壁面パネルに音量調整ボリューム付き
D-TPA1A (パネルは白色)、DS-TPA1A (パネルはシルバー)、DB-TPA1A (パネルは黒色)の 3 種類
機器間の接続は CAT5 ケーブル
電源は FP-TPS4A から CAT ケーブル経由で供給
消費税込み価格
2. FP-TPS4A Format-A オーディオ・センダー ¥29,190






テレビ、コンピューター、タブレット等からのステレオ音声入力
ヘッドホン端子(3.5ST)と RCA ステレオ入力
モノラル平衡入力
2 系統のステレオ出力(RJ45)
最大電流容量:500mA
消費税込み価格
3. TP-HA1A ステレオ・ヘッドホンアンプ ¥23,310




音量調整ボリューム付きステレオ・ヘッドホンアンプ
標準ヘッドホンに 25mW のパワー供給
電源は FP-TPS4A から CAT ケーブル経由で供給
消費税込み価格
株式会社エムアンドエヌ URL http://www.mnsv.co.jp
パワーアンプ内蔵ボリュームパネルでスッキリ!
信号ラインは汎用のLANケーブルで接続可能
DB-TPA1A
32,340円
Format-A オーディオセン
ダーユニット
RCA入力およびヘッドフォン
レベル入力(3.5ST)
3.5W/8Ωパワーアンプ内蔵ボ
リュームコントロールパネル
CAT5
24VDC
FP-TPS4A
29,190円
ステンレス仕上げ DS-TPA1A
白色パネル
D-TPA1A
CAT5
TP-HA1A
23,310円
Speaker Line
Format-A ステレオヘッドフォ
ンアンプ
他にも多彩なコンポーネント
機器が揃っています。
株式会社エムアンドエヌ
〒160-0015 東京都新宿区大京町3 TEL 03-5368-8840 FAX 03-5368-8841
TWISTED PAIR FORMAT-A
Models D-TPA1A, DS-TPA1A, DB-TPA1A
3.5 W Audio Power Amplifier
i






DB-TPA1A
DS-TPA1A
ii
D-TPA1A
3.5 Watt RMS Audio Amplifier into 8 Ohms
6.5 Watt RMS Audio Amplifier into 4 Ohms
Output Drives 4 or 8 Ohm Speaker
Setting Level to Minimum Activates Energy-Saving Sleep Mode
High-Efficiency Class D Operation
VCA Level Adjustment for Scratch-Free Long Life






Input and Power Connection on RJ45
Connects to Format-A Sender using Twisted-Pair Cable
Powered from RDL Twisted Pair Format-A Sender
Speaker Output Connection on Detachable Terminal Block
Ultra-Compact All Metal Construction
Thermal and Short-Circuit Protection
The -TPA1A is part of the group of versatile wall-mounted products from Radio Design Labs. The standard mounting case can be directly fastened in North American
electrical boxes or in RDL International wall boxes.
APPLICATION: The –TPA1A modules are two-pair audio amplifier modules compatible with RDL Format-A twisted pair products.
Each –TPA1A receives stereo audio and 24 Vdc power through a rear-panel RJ45 jack. The left and right audio signals received
on pairs B and C of the twisted pair cable are summed to mono and amplified. The amplified output level is set by an internal VCA
which is controlled by a front-panel volume control. The VCA attenuator provides years of scratch-free gain adjustment.
The –TPA1A circuits are all designed for low power consumption. Amplification is provided by a high-efficiency Class D power
stage with audio filtering tailored for crisp, pleasant audio clarity. The high-efficiency Class D output stage produces negligible heat
for all levels of expected voice or music modulation. When the user reduces the audio level to minimum, the class D output stage
is switched off. This sleep mode remains active until the user turns up the output level.
The output drives either a 4 Ohm or 8 Ohm speaker. The speaker cable connects to the module using a detachable terminal
block.
The front panel does not include any illuminated indicators, making the –TPA1A ideally suited to installation in dark rooms or
areas. Installation is simple and quick, requiring only the connection of the speaker leads and the twisted pair RJ45.
The –TPA1A may be fed and powered from any RDL Format-A sender, and is ideal in hospitality installations fed from a sender
connected to a TV monitor (for example: FP-TPS4A Audio Sender from TV with fixed audio output level).
Use the –TPA1A wherever a single speaker user-adjustable wall mounted amplifier is needed. Combine the amplifier with other
RDL Format-A products for a cost-effective, high-performance audio system.
RDL  659 6th St.  Prescott, AZ., USA 86301  (928) 443-9391  FAX (928) 443-9392  www.rdlnet.com
D- SERIES
Installation/Operation
Models D-TPA1A, DS-TPA1A, DB-TPA1A
EN55103-1 E1-E5; EN55103-2 E1-E4; EN60065
Typical Performance reflects product at publication time exclusive of EMC
data, if any, supplied with product. Specifications are subject to change
without notice. This product is Professional Apparatus.
3.5 W Audio Power Amplifier
Mounting
The –TPA1A should be mounted in an RDL WB-1U wall box or equivalent. The ambient operating environment must not exceed 40 degrees C.
4 OR 8
SPEAKER
AUDIO
Connect Twisted Pair Cable
directly to the output of a
FORMAT A SENDER.
FORMAT A
TP CABLE
4 OR 8
SPEAKER
Adjust gain for the desired listening
the level to minimum will activate the
energy-efficient sleep mode.
DO NOT GROUND
EITHER SPEAKER WIRE
D SERIES - TPA1A
RJ45 Standard wiring
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Pair A: Audio +4 dBu
Pair B: Audio +4 dBu
Pair C: Audio +4 dBu
Pair D: Power +24 Vdc
+ White / Green
– Green
+ White / Orange
– Blue
+ White / Blue
– Orange
+ White / Brown
– Brown
Tab on bottom of connector
RJ45 conductor colors shown are for 568A standard. The 568B standard may be used if the connectors at both ends of the cable are wired identically.
TYPICAL PERFORMANCE
Input:
Input Connector:
Gain Adjustment:
Frequency Response:
THD+N:
Noise:
CMRR:
Output Power:
Power Consumption:
Sleep Mode Power Consumption:
Sleep Mode Enable:
Ambient Operating Environment:
Dimensions:
891-4670
RDL Format-A
RJ45
Single turn audio taper, VCA attenuator
50 Hz to 20 kHz (+/- 1.5 dB)
< 0.1% (@ 1 kHz, 1 W)
<-70 dB (below 1 W RMS)
> 60 dB (50 Hz to 120 Hz)
3.5 W RMS (max., into 8 Ohms); 6.5 W RMS (max., into 4 Ohms)
45 mA (idle), 95 mA (1 W into 8 Ohms), 150 mA (1 W into 4 Ohms), 215 mA (3.5 W into 8 Ohms)
< 0.3 W
Active at audio gain <-60 dB
0° C to 40° C Maximum; 20° C Recommended
Height: 4.13 in. 10.49 cm; Width: 1.7 in. 4.32 cm; Depth: 2.15 in. 5.47 cm
Radio Design Labs Technical Support Centers
U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506
Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287
TWISTED PAIR FORMAT-A
Model FP-TPS4A
Format-A Two-Pair Audio Sender









Format-A Sender from TV Fixed Audio Output
Sends Left and Right Audio Channels
Unbalanced Stereo Input from Fixed Level Audio Source
Balanced Audio Input from Mono Amplifier
High Quality Audio Distributed to Each RJ45 Output
Two Format-A Outputs on RJ45
Distributes Power to Connected Receivers
Automatically Resetting Fuse for Output Voltage
Ultra-Compact All Metal Construction
i
i
The FP-TPS4A is part of the group of versatile FLAT-PAK products from Radio Design Labs. The unique FLAT-PAK case can be directly screwed
or bolted to cabinets or shelves. Optionally available rack-mounting accessories permit single or multiple FLAT-PAK module mounting.
APPLICATION: The FP-TPS4A is an RDL Format-A Audio Sender that accepts either a stereo line-level or 1 to 3
Watt mono amplified fixed-level signal, usually from a commercial hospitality equipped TV. The FP-TPS4A
distributes the source signal to two Format-A output jacks to feed multiple Format-A receivers.
The input accepts either an unbalanced stereo or an amplified mono input. The FP-TPS4A sends the unbalanced
Left and Right sources over balanced twisted-pair cables on pairs B and C. If a mono amplified signal is connected,
the mono source is fed to both pairs B and C. Audio circuitry is active balanced for superior audio fidelity and
low-noise performance.
The FP-TPS4A is normally mounted behind a TV where AC power is available. A 24 Vdc power supply, available
separately, provides power to the FP-TPS4A and to the connected receiving modules. It is not necessary to connect
power supplies to the connected receivers, facilitating installation. A front-panel blue LED is illuminated when the
FP-TPS4A is receiving and distributing 24 Vdc to both RJ45 jacks. The distributed output dc voltage is short-circuit
protected by an automatically resetting fuse. A power fault on either output jack causes the blue LED to extinguish.
The FP-TPS4A is ideally suited to guest room installations with bedside and restroom listening stations. The outputs
are fully compatible with all RDL Format-A receivers.
RDL FORMAT-A features superior audio performance that rivals or exceeds shielded wiring. Design simplicity, ease
of installation, unsurpassed flexibility, automatic fused power, exceptional hum rejection, low noise, and low distortion
provide designers and installers the optimum choice in economical twisted pair products.
RDL  659 6th St.  Prescott, AZ., USA 86301  (928) 443-9391  FAX (928) 443-9392  www.rdlnet.com
FLAT-PAK™ SERIES
Installation/Operation
Model FP-TPS4A
EN55103-1 E1-E5; EN55103-2 E1-E4; EN60065
Typical Performance reflects product at publication time exclusive of EMC
data, if any, supplied with product. Specifications are subject to change
without notice. This product is Professional Apparatus.
Format-A Two-Pair Audio Sender
AUDIO CONNECTION
POWER CONNECTION
Fixed Line-Level Source (TV fixed
audio output programmed to remain
active when TV audio is muted.)
INPUTS
Connect only one
set of inputs.
OUTPUTS
INPUTS
RDL 24 VDC
POWER SUPPLY
LEFT
24 VDC
LEF
24 VDC
RIGHT
Fixed Amplified Source (TV fixed
level audio output from a nominal 2
Watt, 4 or 8 Ohm amplified output;
Minimum 1 W, Maximum 10 W)
UNBALANCED
LINE INPUTS
RIG
UNBALANCED
LINE INPUTS
POWER
AMPLIFIED AUDIO INPUT - BALANCED MONO
AMPLIFIED AUDIO INPU
RECEIVER CONNECTIONS
Connect one or more FORMAT A Receivers
to one or both OUTPUTs. (Maximum total
connected receiver load: 500 mA)
RJ45 Standard Wiring
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Pair A: Audio +4 dBu
Pair B: Audio +4 dBu
Pair C: Audio +4 dBu
Pair D: Power +24 Vdc
+ White / Green
– Green
+ White / Orange
– Blue
+ White / Blue
– Orange
+ White / Brown
– Brown
Tab on bottom of connector
RJ45 conductor colors shown are for 568A standard. The 568B standard may be used if the connectors at both ends of the cable are wired identically.
TYPICAL PERFORMANCE
Inputs (3):
Input Connection:
Input Level:
Format-A Signal Pairs Used (2):
Output:
Output Connection:
Frequency Response:
THD+N:
Noise below +4 dBu:
Crosstalk:
Headroom above +4 dBu:
Indicator:
Power Connection:
Power Requirement:
Maximum Load Current:
Dimensions:
891-2175
20 kΩ unbalanced (2, left and right); 100 kΩ balanced (mono amplified)
Phono Jack (Unbal.); Mini-jack (Bal.)
-10 dBV unbalanced; 1 W (8 Ohms) to 10 W (8 Ohms) balanced, 2 W nominal
B, C
RDL TP Format-A
RJ45
10 Hz to 50 kHz (+/- 0.1 dB)
< 0.05%
< -85 dB
< -85 dB (10 Hz to 10 kHz); < -80 dB (10 kHz to 20 kHz)
> 18 dB
Power (Input and outputs active)
Power Jack (locking)
24 Vdc @ 30 mA plus connected loads
500 mA
4.15" (10.5 cm) L; 3.25" (8.6 cm) W; 1.68" (4.27 cm) H
Radio Design Labs Technical Support Centers
U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506
Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287
TWISTED PAIR FORMAT-A
Model TP-HA1A
Format-A Stereo Headphone Amplifier










Headphone Amplifier with User Level Control
25 mW Power into Standard Headphones
Output on Standard Mini Jack
Mounts to Any Flat Surface
Input and Power Connection on RJ45
Connects to Format-A Sender using Twisted-Pair Cable
Powered from RDL Twisted Pair Format-A Sender
RJ45 Loop-Thru for Connecting Additional Modules
Protected by Automatically Resetting Fuse
Ultra-Compact All Metal Construction
i
i
The TP-HA1A is part of the group of versatile Twisted Pair products from Radio Design Labs. The unique case can be directly screwed or bolted to
cabinets, shelves or furniture.
APPLICATION: The TP-HA1A is a two-pair receiver and audio headphone amplifier compatible with RDL Format-A
twisted pair products. Each TP-HA1A receives stereo audio and 24 Vdc power through a rear-panel RJ45 jack fed
from a Format-A sender. The left and right audio signals received on pairs B and C of the twisted pair cable are
amplified and fed to the left and right channels of the output 3.5 mm Mini-jack.
The front panel provides the headphone output jack and a single-turn user volume control. There are no illuminated
indicators that could be distracting in dark locations, such as a hotel room. The audio input circuits feature very high
common mode rejection and a high quality stereo headphone amplifier for superior audio fidelity and low-noise
performance.
The TP-HA1A is ideally suited to guest room installations with bedside and restroom listening stations. The input is
fully compatible with all RDL Format-A senders.
The TP-HA1A is equipped with two Format-A RJ45 jacks. Either jack may be used as the input. The other RJ45
may be used to connect an additional TP-HA1A or other Format-A receiver.
Installation is simple and economical. Standard twisted pair cable is used to connect a Format-A sender to the
TP-HA1A. The base plate of the TP-HA1A has cutouts that allow installers to pre-wire the twisted pair cable with
RJ45 connectors attached. The finished twisted pair cable/connector can be fed through the base plate prior to
mounting. The base plate is mounted with two screws, the twisted pair cable is plugged in, then the cover plate is
attached with one screw.
RDL FORMAT-A features superior audio performance that rivals or exceeds shielded wiring. Design simplicity, ease
of installation, unsurpassed flexibility, automatic fused power, exceptional hum rejection, low noise, and low distortion
provide designers and installers the optimum choice in economical twisted pair products.
RDL  659 6th St.  Prescott, AZ., USA 86301  (928) 443-9391  FAX (928) 443-9392  www.rdlnet.com
TWISTED PAIR FORMAT-A
Installation/Operation
Model TP-HA1A
EN55103-1 E1-E5; EN55103-2 E1-E4; EN60065
Typical Performance reflects product at publication time exclusive of EMC
data, if any, supplied with product. Specifications are subject to change
without notice. This product is Professional Apparatus.
Format-A Stereo Headphone Amplifier
MOUNTING DETAILS
Route Twisted Pair wire
and connector through
wire entry cutout.
WIRING CONNECTIONS
Use screws to secure
the base plate to its
mounting surface.
Connect FORMAT A
Twisted Pair Cable to an
additional TP-HA1A or
other Format-A
Receiver.
Connect FORMAT A
Twisted Pair Cable from
a Format-A Sender.
AMPLIFIER
AMPLIFIER
KNOB
STANDOFF
TOP VIEW
(COVER REMOVED)
Pull off to
remove.
In the event of damage to the amplifier, it can
be quickly replaced. Remove the knob and the
standoff. Lift the amplifier out of the base plate.
Fit the new amplifier in its place. Replace the
standoff and knob.
FRONT VIEW
RJ45 Standard Wiring
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Pair A: Audio +4 dBu
Pair B: Audio +4 dBu
Pair C: Audio +4 dBu
Pair D: Power +24 Vdc
+ White / Green
– Green
+ White / Orange
– Blue
+ White / Blue
– Orange
+ White / Brown
– Brown
Tab on bottom of connector
RJ45 conductor colors shown are for 568A standard. The 568B standard may be used if the connectors at both ends of the cable are wired identically.
TYPICAL PERFORMANCE
Input:
Input Connection:
Format-A Signal Pairs Used (2):
Format-A Output:
Output:
Frequency Response:
THD+N:
Noise:
Crosstalk:
Power Connection:
Power Requirement:
Dimensions:
891-4665
RDL TP Format-A
RJ45
B, C
RJ45 (loop-through)
Stereo, 25 mW per channel (into 100 ohms)
10 Hz to 40 kHz (+/- 1 dB, into 100 Ohms)
< 0.01% (1 kHz, 10 mW)
< -90 dB (maximum gain)
< -85 dB (1 kHz); < -70 dB (20 Hz to 20 kHz)
RJ45 (power provided by Format-A sender)
24 Vdc @ 30 mA
3.9" (9.92 cm) L; 2.57" (6.53 cm) W; 1.13" (2.87 cm) H
Radio Design Labs Technical Support Centers
U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506
Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287
Fly UP